حدد صفحة

A Adjustable Frequency Drive (VFD) is a type of electric motor controller that drives an electric engine by varying the frequency and voltage supplied to the electric motor. Other brands for a VFD are variable speed drive, adjustable swiftness drive, adjustable frequency drive, AC drive, microdrive, and inverter.
Frequency (or hertz) is directly related to the motor’s swiftness (RPMs). Basically, the quicker the frequency, the quicker the RPMs go. If a credit card applicatoin does not require a power motor to perform at full quickness, the VFD can be used to ramp down the frequency and voltage to meet certain requirements of the electrical motor’s load. As the application’s motor rate requirements modify, the VFD can merely turn up or down the electric motor speed to meet up the speed requirement.
The first stage of a Variable Frequency AC Drive, or VFD, is the Converter. The converter is definitely made up of six diodes, which are similar to check valves used in plumbing systems. They enable current to stream in only one direction; the direction demonstrated by the arrow in the diode symbol. For example, whenever A-phase voltage (voltage is similar to pressure in plumbing systems) is certainly more positive than B or C phase voltages, after that that diode will open up and invite current to circulation. When B-stage turns into more positive than A-phase, then the B-phase diode will open up and the A-stage diode will close. The same holds true for the 3 diodes on the adverse side of the bus. Thus, we obtain six current “pulses” as each diode opens and closes. That is called a “six-pulse VFD”, which may be the standard configuration for current Adjustable Frequency Drives.
Let us assume that the drive is operating upon a 480V power program. The 480V rating is definitely “rms” or root-mean-squared. The peaks on a 480V system are 679V. As you can see, the VFD dc bus includes a dc voltage with an AC ripple. The voltage operates between approximately 580V and 680V.
We can get rid of the AC ripple on the DC bus with the addition of a capacitor. A capacitor functions in a similar fashion to a reservoir or accumulator in a plumbing system. This capacitor absorbs the ac ripple and delivers a soft dc voltage. The AC ripple on the DC bus is normally less than 3 Volts. Thus, the voltage on the DC bus becomes “around” 650VDC. The actual voltage depends on the voltage level of the AC series feeding the drive, the amount of voltage unbalance on the power system, the engine load, the impedance of the power program, and any reactors or harmonic filters on the drive.
The diode bridge converter that converts AC-to-DC, may also be just known as a converter. The converter that converts the dc back again to ac can be a converter, but to tell apart it from the diode converter, it is generally known as an “inverter”. It has become common in the market to refer to any DC-to-AC converter as an inverter.
Whenever we close among the top switches in the inverter, that stage of the engine is connected to the positive dc bus and the voltage upon that phase becomes positive. Whenever we close among the bottom level switches in the converter, that phase is connected to the detrimental dc bus and turns into negative. Thus, we are able to make any phase on the electric motor become positive or detrimental at will and may thus generate any frequency that people want. So, we can make any phase maintain positivity, negative, or zero.
If you have a credit card applicatoin that does not need to be operate at full acceleration, then you can decrease energy costs by controlling the motor with a adjustable frequency drive, which is among the advantages of Variable Frequency Drives. VFDs allow you to match the quickness of the motor-driven products to the strain requirement. There is no other method of AC electric engine control which allows you to do this.
By operating your motors at most efficient rate for your application, fewer errors will occur, and therefore, production levels increase, which earns your company higher revenues. On conveyors and belts you get rid of jerks on start-up enabling high through put.
Electric motor systems are accountable for a lot more than 65% of the power consumption in industry today. Optimizing electric motor control systems by installing or upgrading to VFDs can reduce energy consumption in your facility by as much as 70%. Additionally, the use of VFDs improves item quality, and reduces creation costs. Combining energy effectiveness taxes incentives, and utility rebates, returns on purchase for VFD installations can be as little as 6 months.

Do you have any recommendations on the محرك متغير السرعةمن فضلك لا تفكر مرتين في الاتصال بنا.

رمز القائمة اليسرى